- Home
- »
- Our Products
- »
- ARDUINO BOARDS
ARDUINO BOARDS
ARDUINO NANO
ARDUINO 2560
ARDUINO CH340
18650 Lithium Battery Charging Module Protection
Current | 1 A adjustable |
Charge Precision | 1.5% |
Input Voltage | 4.5 V-5.5 V |
Full Charge Voltage | 4.2 V |
Work Temperature | 10 C to +85 C |
Size | 27 x 17 mm |
- 100% brand new and high quality
- Charge module- Linear charging.
- It has MICRO USB female
- It still retain the input voltage wiring solder joints, can be very convenient to DIY.
Specifications:
- Led indicator- red is charging Green is full charged.
- Input interface- micro USB.
- Inversed polarity- NO.
Arduino Uno R3
Operating Voltage | 5V |
Current | 500mA |
Dimension | 30 mm X 47 mm |
Packaging Type | Box |
Micro USB 4.5V-5.5V 1A Lithium Lipo Battery Charger Module
Charging Current | 1 A |
External Dimension | 25 x 19 x 10 mm |
Full Charger Pressure | 4.2 V |
Input Voltage | 4.5 V - 5.5 V |
- Module name: Lithium battery charging board
- Charging mode: Linear charge
- Charging indicator: Charging red light - blue light full charge
- Input interface: Mini USB
- Can reverse: Inverted
Arduino Yun Original
Minimum Order Quantity: 3 Piece
Product Generation | ARDUINOYUN |
Brand | ARDUINO BOARD |
Model Number | YUN |
The Arduino YÚN is the combination of a classic Arduino Leonardo (based on the Atmega32U4 processor) with a WiFi system-on-chip running OpenWrt-Yun (a GNU/Linux distribution based on OpenWrt). We embedded the Linux machine directly on the PCB of the Arduino Leonardo and we connected the two so that from Arduino it's very easy to run commands on the Linux side and use it as an Ethernet and WiFi interface.
Warning: Arduino YÚN is not compatible with 12V PoE module.
Arduino Mega 2560 R3
Input Voltage | 7-15 V |
Frequency | 72 MHz |
Usage | Laboratory |
Power Supply | 12 VDC |
L293d Arduino Based Motor Sheild
Color | Blue |
Brand | Arduino |
Molar Number | L293D |
Current Type | DC |
Current rating | 2.0 A, AC DC |
Power Source | Electric |
Voltage | 24 V |
This Arduino compatible motor Driver shield is a full-featured products that it can be used to drive 4 DC motors or two 4-wire stepper and two 5V 'hobby' servo. It drive the DC motor and stepper with the L293D, and it drive the servo with Arduino's pin9 and pin10.
Features:
- 2 x L293D Motor Control Chips
- Total of 4 H-Bridges for controlling 4 DC motors or 2 Stepper motors
- 2 x Server ports for controlling RC Hobby Servos
- The logic control voltage Vss: 4.5~5.5V
- Motor Supply Voltage: 4.5 ~ 12V
- Reduced control pins needed through 8-stage serial shift registers
- Drive part of the operating current Io: 1.2A (0.6A per bridge)
- External power connection via a screw-terminal block
- Screw-Terminal blocks for connection to motors
Additional Information:
- Item Code: L293D
- Pay Mode Terms: T/T (Bank Transfer)
- Delivery Time: 6-12 DAYS
Prototype with Breadboard Shield for Arduino UNO
Weight | 31 g |
Color | Blue, black, white |
Brand | Arduino |
Prototype size | 6.8 * 5.4 * 2 cm |
Mini breadboard size | 4.7 * 3.5 * 0.9 cm |
Application | Automobile |
Description:
ProtoShield is used in conjunction with Arduino Duemilanove.
Used to build a circuit prototype, can be directly soldered components on the board.
Can also be connected through the mini breadboard circuit.
1 reset button, 1 general use button, and 2 LED circuits can be used directly.
5V, GND, and Raw pins are exposed as well.
The mini breadboard has 170 tie points.
SOIC place for IC.
The breadboard sticks on the prototype shield with its self-adhesive backing.
Multi - Function Shield
Dimensions | 69 x 54 x 11 |
Weight | 27 gm |
Display | LED |
Power Source | Electric |
Application | Industrial |
Power Supply | 5 V |
Multi - Function Shield has a wide range of features which makes it perfect for beginners who want to study. It can be useful for advanced users because it has built-in general purpose components:
USB Host Shield for Arduino
Operating Voltage | 5V |
USB Controller | MAX3421E |
Max Current with Arduino | 500mA |
Max Current with USB Port | 400mA |
Voltage | 3.3/5V |
Application | Automobile |
Features
- USB 2.0 Full Speed compatible
- 3.3/5V operation level compatible
- All GPIOx pins break-out
- USB Host 5V/500mA supply for USB protocol
Prototype Shield V3 Mini Bread Board for Arduino MEGA
Power Source | Electric |
Voltage | 24 V |
Frequency | 50 Hz |
Type | Prototype |
Application | Automobile |
Power Supply | 5 V |
The board can not only receive MEGA seamless plug controller, directly soldered to the above components to complete a variety of prototype circuit, you can paste Mini bread board, through the 7-color jumper to complete a variety of circuit experiment , board integrated power indicator and status lights, and reset buttons, easy to learn MEGA preferred prototype controller expansion board.
- 1. Arduino MEGA / MEGA2560 ProtoShield prototype expansion board with Immersion Gold PCB processing technology, motherboards, small gold square pad spacing, welding components easier.
- 2.SOP28 SMD component package to be more handy Arduino electronics enthusiasts will not be directly insert bound components.
- 3. The board can receive Arduino MEGA / MEGA2560 seamless plug controller, directly soldered to the above components to complete a variety of prototype circuit, you can paste Mini bread board, through the 7-color jumper to complete a variety of circuit experiment , board integrated power indicator and status lights, and reset buttons, easy to learn Arduino MEGA / MEGA2560 preferred prototype controller expansion board.
- 4. Full Compatible with Arduino Mega ATmega1280 / MEGA2560.
- 5. High sensitivity with integrated low-noise RF input amplifier.
Arduino Wifi Shield ESP13 Web Sever Serial Wi-Fi Expansion
Brand | Arduino |
Wireless transmission rate | 110-460800 BPS |
Working temperature | - 40 + 125 |
Modules weight | About 20 g |
Model Number | ESP13 |
Application | Industrial |
Working current | 70 ma, 200 ma |
Arduino Wifi Shield ESP13 Web Server Serial Wi-Fi Expansion
Features:
2. standard pin compatible with the Ar-duin Uno, Me ga2560, such as main control board, a voltage conversion chip is used to connect with the Ar-duin Uno, 3.3V and 5V compatible;
3. a serial port using dual dial the code switch to control, makes the extension board can separate as Ar-duin Uno extended board is used, can also be used as ESP8266 extension plate;
4. Real serial WiFi, the Ar-duin program without any configuration;
5. WiFi based on the Web Server configuration parameters and serial port;
6. Can be used as an independent ESP8266 development board, download the official firmware the AT command, Node MCU open-source firmware, etc;
7. Can be used as an independent Ar-duin Uno expansion board, pins all leads.
Specifications:
1. Support wireless 802.11 b/g/n standard;
2. Support the STA/AP two working mode;
3. Built-in TCP/IP protocol stack, you can configure a socket;
4. Support the standard TCP/UDP Server and Client;
5. A serial port baud rate support: 1200/2400/4800/9600/4800/9600/57600/74800/115200 BPS.
6. A serial port data bits: 5/6/7/8;
7. Serial ports, parity: no;
8. Serial ports, stop bit: 1/2;
9. Standard Ar-duin UNO, Me ga pin spacing;
10. Which leads to the Ar-duin Pin 2/3/4/5/6/7/8/9/10/11/12/13;
11. Which leads to the ESP8266 GPIO 0/2/4/5 9/10/12/13/14/15/16 / ADC/EN/UART TX/UART RX.
12. RESET RESET;
13. KEY buttons reuse configuration function;
14. Two dial the code switch to realize the Ar-duin and ESP8266 serial port extension switch;
15. WiFi working current: continue to send: material 70 ma 200 ma (MAX), standby: < 200 ua;
LCD Shield
Minimum Order Quantity: 20 Piece
Brand | Arduino |
Depth | 130.05 mm |
Display | 16x2 |
Operating Voltage | 5V |
Push buttons | 6 |
Display Type | LCD |
Description: This is a 16x2 LCD and Keypad shield for Arduino Uno, Diecimila, Duemilanove and Freeduino boards. to provide a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 5 keys — select, up, right, down, left and reset. To save the digital IO pins, the keypad interface uses only one ADC channel. The key value is read through a 5 stage voltage divider.
M30 Starter Kit
Model | M30 |
Device Dimensions | 16.3 mm x 14 mm x 2.24 mm (Chipset Size) |
The Range of Baudrate | 1200~115200 bps |
Frequency | 2.4 GHz |
- 2.4GHz 802.11b/g/n,compatible
- WiFi Sta/Soft AP Mode
- Support Smart Connection
- Support transparent transmission mode
Support multiple security authenti-cation mechanisms:
- WEP64/WEP128/ TKIP/ AES
- WEP/WPA-PSK/WPA2-PSK
- Support wireless roam
- Support multiple network protocols:
- TCP/UDP/ /DHCP/DNS
- Support AT instruction Set
Applications:
- WiFi Led Control
- WiFi Power Switch
- Smart Home; Smart Building
- OBDII WiFi Diagnose
- RFID Data Transfer
- Toys and Gaming Peripherals
- Industrial Systems
- Telemetry
- Remote Control
Data Logger Shield For Arduino
Usage/Application | Industrial |
Battery | CR1220 |
Dimension | 68 x 53 x 23 mm |
Voltage | 12 V |
Usage | Students Project |
Bread Board Power Supply Module
Usage/Application | Industrial |
Frequency | 50 - 60 Hz |
Voltage | 3.3V & 5V Output |
Power Source | Electric |
Packaging Type | Box |
Freeduino Nano CH340 Based
Clock Speed | 16 MHz |
Operating Voltage | 5 V |
Input Voltage | 7-12 V |
Packaging Type | Box |
Ethernet Shield W5100 For Arduino
Weight | 18 - 21.8g |
Flash Memory | 4MB |
Operating Voltage | 3.3V |
Power Source | Electric |
Arduino Campatible Mini Pro 5V 16M Board
Power | 3 - 5V |
Current | 150mA |
Input Voltage | 6-20V |
Power Source | Electric |
MQ-4, Methane CNG Gas Sensor Module
Product Brochure
Model / Part Number | MQ-4 |
Target gases | CH4, Natural gas. |
Application | Industrial |
Operating Voltage | 5 V |
Operating Humidity | 0-95%RH |
Preheat Duration | Over 24 hour |
Packaging Type | Box |
Power Source | Electric |
Circuit voltage | 5V+-0.1 |
Load resistance | 20K ohm |
Heater resistance | 33 ohm +-5% |
2.4 Inch LCD TFT Display
Size | 2.4" |
Usage/Application | Automobile |
Power Source | Electric |
Frequency | 50 Hz |
Voltage | 220 V |
Application | Industrial |
Features:
2.4 inch LCD TFT display
Bright, 4 white-LED backlight, on by default but you can connect the transistor to a digital pin for backlight control
Colorful, 18-bit 262,000 different shades
4-wire resistive touchscreen
240 x 320 resolution
Spfd5408 controller with built in video RAM buffer
8 bit digital interface, plus 4 control lines
Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the micro SD
5V compatible, use with 3.3V or 5V logic